auger adapter

[阿青fishing]

ebay 买的 今天刚收到

[阿青fishing]

[阿青fishing]

等着明天最后一次上冰用下 看看

[creativeccc]

看着不错哦， 黑色那头是什么材料？有没有LINK分享一下吧

[Sergeantpepper]

Looks like a steel allen key (handle portion) force-fitted into a turned aluminum adaptor....should be more tough going than the zinc die-casted one

[yangzw2002]

多少刀一个？

[阿青fishing]

多少刀一个？

24+12.11 刀

[阿青fishing]

Looks like a steel allen key (handle portion) force-fitted into a turned aluminum adaptor....should be more tough going than the zinc die-casted one

希望比那 锌合金耐用

[边走边钓]

这个没有见过？和SAIL买的那个10刀的有区别吗？

[Sergeantpepper]

http://www.ebay.ca/itm/Eskimo-Ice-Auger-Adapter-for-Cordless-Drill-Ice-Fishing-/180595708863

[DIYUSOCCERLO]

Watch out the adapter and the auger go straight down to the bottom.
Serg, you know what I mean

[yangzw2002]

多少刀一个？

24+12.11 刀

看上去不错

[Sergeantpepper]

It usually happens when the auger is being pulled out of the done hole, one thing one can do is to hold the flute of the auger instead of the handle of the drill when one pulls, and often retighten the chuck on the drill...

[XUYCA]

要DIY一个保护盘。否则，打洞多了，会出现松动。钻头会掉下去。

[abc27]

这个adapter在CT和Sail都有卖, 就是$10块左右的东西

但是这个不好用,因为钻头会抖得很厉害. 你都花了快30了,还不如去bps买个clam的adapter,那个也就70多,但是一套完整了

[Sergeantpepper]

要DIY一个保护盘。否则，打洞多了，会出现松动。钻头会掉下去。

那drop proof 東東不一定要碟形, 6吋手钻就按原耒的 wing screw 去配条 threaded rod,开7至8吋長夠了吧,, 插上adaptor 后把threaded rod 一半修过去, 在进入那边加上弹弓介指和nut...完成

[阿青fishing]

要DIY一个保护盘。否则，打洞多了，会出现松动。钻头会掉下去。

6寸钻有个8寸的硬塑料底盘 就算滑出来也不会掉到洞里去

[阿青fishing]

要DIY一个保护盘。否则，打洞多了，会出现松动。钻头会掉下去。

那drop proof 東東不一定要碟形, 6吋手钻就按原耒的 wing screw 去配条 threaded rod,开7至8吋長夠了吧,, 插上adaptor 后把threaded rod 一半修过去, 在进入那边加上弹弓介指和nut...完成

怎么做 有图片么

[Sergeantpepper]

threaded rods are usually used as tie rods for hanging ceiling fixture
you can bring that wing -screw to match the right nut to confirm the diameter and thread form of the threaded rod that you should look for.....most mega hardware shops should stock them

[Sergeantpepper]

也可以造单边的
用囗6吋長的 bolt 跟原来的 wing screw 一样修过去再加个 lock nut 就是