分页: 1 / 2

My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 12:55
风帆扬
Long story short, I cut each a piece of a paint mixer and manual auger handle, then use a $30 welder bought from kijiji, finished my first welding project.

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 13:05
sunfish123
赞一个,不知道强度够不够

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 13:05
Bluelake
Well done. :up
电焊机不错,只要30

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 13:09
Pungo
Could be better aligned.

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 13:12
Pungo
Pungo @ Mon Dec 30, 2019 12:09 pm 写道: Could be better aligned.

转动的东西,不同心,不同轴,很危险的。

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 13:25
jimi
动手能力点个赞,图个乐,不错 :up

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 13:51
jasontoronto
:up
等着使用情况报告。

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 13:59
阿恩
先赞一个,如果纯粹为了兴趣,可以玩玩。但其实并不如果做好,一个是强度,一个是alignment的问题,另外买一个现成不锈钢的也不贵。

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 14:31
风帆扬
多谢楼上各位回帖, 强度的问题不好说, 要试过才知道, 看焊接质量。 如果焊接好的话焊接部位强的实际上超过其他地方。 偏心的问题, 像这样是开放式的,稍微有点偏心应该问题不大。 也要试过才知道。 请教一下 drill是1 or 2档?

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 14:35
xiaolu
jsyangyu @ Mon Dec 30, 2019 1:31 pm 写道: 多谢楼上各位回帖, 强度的问题不好说, 要试过才知道, 看焊接质量。 如果焊接好的话焊接部位强的实际上超过其他地方。 偏心的问题, 像这样是开放式的,稍微有点偏心应该问题不大。 也要试过才知道。 请教一下 drill是1 or 2档?

放在 1 裆(低速),是必须的。

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 14:44
Fishingdaddy
建议楼主做个放掉装置再上冰试验。

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 14:52
Sergeantpepper
牛呀 :up

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 14:54
风帆扬
Fishingdaddy @ 30 Dec 2019 13:44 写道: 建议楼主做个放掉装置再上冰试验。

Will do :shake

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 14:54
Sergeantpepper
Fishingdaddy @ Mon Dec 30, 2019 1:44 pm 写道: 建议楼主做个放掉装置再上冰试验。


防放差別極端呀 :laugh3

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 14:58
wetnose
Sergeantpepper @ Mon Dec 30, 2019 1:54 pm 写道:
Fishingdaddy @ Mon Dec 30, 2019 1:44 pm 写道: 建议楼主做个掉装置再上冰试验。


防放差別極端呀 :laugh3

:+1

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 15:28
Fishingdaddy
Sergeantpepper @ 30 Dec 2019 13:54 写道:
Fishingdaddy @ Mon Dec 30, 2019 1:44 pm 写道: 建议楼主做个放掉装置再上冰试验。


防放差別極端呀 :laugh3

在这个坛子学坏了,总打错字,还不觉得错了 :laugh3

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 15:48
johndxu
jsyangyu @ 30 12月 2019 11:55 写道: Long story short, I cut each a piece of a paint mixer and manual auger handle, then use a $30 welder bought from kijiji, finished my first welding project.

welder $30 好价钱啊。我刚勃克兴天在CT买了Welder,$150

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 17:01
风帆扬
johndxu @ 30 Dec 2019 14:48 写道:
jsyangyu @ 30 12月 2019 11:55 写道: Long story short, I cut each a piece of a paint mixer and manual auger handle, then use a $30 welder bought from kijiji, finished my first welding project.

welder $30 好价钱啊。我刚勃克兴天在CT买了Welder,$150

你这个更高级一些。
Level one: Arc Ac (mine)
Level two: Arc inverted Dc
Level three: MiG/tig

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 19:04
Sergeantpepper
MIG/TIG 一般用不著吧, 要用 argon呀 :fishb no?

Re: My very first welding project- an auger adapter

帖子发表于 : 30 12月 2019 20:28
风帆扬
Sergeantpepper @ 30 Dec 2019 18:04 写道: MIG/TIG 一般用不著吧, 要用 argon呀 :fishb no?

Yes or no.
Mig= metal insert gas(argon).
Flux means flux in wire, like soldering wire, no gas need.
Tig=tungsten insert gas

So John can use the flux function without gas tank.

Re: My very first welding project- an auger adapter

帖子发表于 : 31 12月 2019 07:53
Sergeantpepper
下图可见auger 和cordless drill 的 eccentricity 相当明顯 (除非chuck頭未完全上緊)
可以先把auger 卸下, 把DIY adapter 上钻, 开动后觀察adapter 末端摆动情况
这个摆动幅度在auger 切削端會放大五倍六倍吧 (按auger長度推算)
小心使用為上....出洞时最好把原装手抦也帶上, 你明的 :)

Re: My very first welding project- an auger adapter

帖子发表于 : 31 12月 2019 09:37
风帆扬
Sergeantpepper @ 31 Dec 2019 06:53 写道: 下图可见auger 和cordless drill 的 eccentricity 相当明顯 (除非chuck頭未完全上緊)
可以先把auger 卸下, 把DIY adapter 上钻, 开动后觀察adapter 末端摆动情况
这个摆动幅度在auger 切削端會放大五倍六倍吧 (按auger長度推算)
小心使用為上....出洞时最好把原装手抦也帶上, 你明的 :)

多谢了,我是想着今天要调节一下。 :up

Re: My very first welding project- an auger adapter

帖子发表于 : 31 12月 2019 12:15
johndxu
Welding Accessaries.jpg
jsyangyu @ 30 12月 2019 19:28 写道:
Sergeantpepper @ 30 Dec 2019 18:04 写道: MIG/TIG 一般用不著吧, 要用 argon呀 :fishb no?

Yes or no.
Mig= metal insert gas(argon).
Flux means flux in wire, like soldering wire, no gas need.
Tig=tungsten insert gas

So John can use the flux function without gas tank.

看来你很懂Welding,俄狠狠久以前玩过AC和Gas的Welding。这个Welding Machine 俄买了还没打开,这个价格这个功能太赞了。还带配件,打开就能用。

FEATURES
Mastercraft Mig and Flux Welder can be used for both MIG and flux core wire
Infinite wire speed control
Four setting heat selection
MIG and flux core polarity control - quickly and easily change polarity settings
High-efficiency transformer
Thermal overload protection with light
Drive deck with dedicated power supply - helps to maintain constent wire speed
2-in-1 spool holder, spool adaptor for 4" (10 cm) and 8" (20 cm) spool wires

Re: My very first welding project- an auger adapter

帖子发表于 : 31 12月 2019 12:24
johndxu
jsyangyu @ 31 12月 2019 08:37 写道:
Sergeantpepper @ 31 Dec 2019 06:53 写道: 下图可见auger 和cordless drill 的 eccentricity 相当明顯 (除非chuck頭未完全上緊)
可以先把auger 卸下, 把DIY adapter 上钻, 开动后觀察adapter 末端摆动情况
这个摆动幅度在auger 切削端會放大五倍六倍吧 (按auger長度推算)
小心使用為上....出洞时最好把原装手抦也帶上, 你明的 :)

多谢了,我是想着今天要调节一下。 :up

你应该找一个适当的Hex Bit Socket 焊上去,这样比较容易保持同心。

Re: My very first welding project- an auger adapter

帖子发表于 : 31 12月 2019 13:05
风帆扬
johndxu @ 31 Dec 2019 11:24 写道:
jsyangyu @ 31 12月 2019 08:37 写道:
Sergeantpepper @ 31 Dec 2019 06:53 写道: 下图可见auger 和cordless drill 的 eccentricity 相当明顯 (除非chuck頭未完全上緊)
可以先把auger 卸下, 把DIY adapter 上钻, 开动后觀察adapter 末端摆动情况
这个摆动幅度在auger 切削端會放大五倍六倍吧 (按auger長度推算)
小心使用為上....出洞时最好把原装手抦也帶上, 你明的 :)

多谢了,我是想着今天要调节一下。 :up

你应该找一个适当的Hex Bit Socket 焊上去,这样比较容易保持同心。

Good idea but most hex are 3/8 .