[DIY]Fishing for ideas:打算重新整一个Smitty Sled(雪上飞),请您给出点儿高招

相约钓鱼, 探讨钓技, 结交钓友, 分享渔获 。。。

Re: [DIY]Fishing for ideas:打算重新整一个Smitty Sled(雪上飞),请您给出点儿高招

楼层:#151  帖子XUYCA » 19 12月 2018 13:40

这个看着挺结实。
您没有权限查看这个主题的附件(帖图)。 请先注册并登陆后访问。 谢谢! You have no permission to view this attachment. Please register and sign in. Thank you!
XUYCA
Grand General (大将)
Grand General (大将)
 
帖子: 20440
注册: 17 9月 2013 09:45
Member Number (论坛会员注册序列号): #8
地址: 密室 Mississauga
称呼: 院长

Re: [DIY]Fishing for ideas:打算重新整一个Smitty Sled(雪上飞),请您给出点儿高招

楼层:#152  帖子xiaolu » 19 12月 2018 14:02

XUYCA @ Wed Dec 19, 2018 12:40 pm 写道: 这个看着挺结实。



上面的辣个长方型的 PVC 框架, 看上去不是很方便拆卸, 这个长方型的 PVC 框架不能快速方便的拆卸的话, 整个雪上飞放不进去我的小烂车, 还是白搭....
xiaolu
Site Admin (站长)
 
帖子: 42626
注册: 17 9月 2013 06:22
Member Number (论坛会员注册序列号): #1
地址: Maple, Vaughan

Re: [DIY]Fishing for ideas:打算重新整一个Smitty Sled(雪上飞),请您给出点儿高招

楼层:#153  帖子jimi » 19 12月 2018 14:11

xiaolu @ 周三 12月 19, 2018 1:02 pm 写道:
XUYCA @ Wed Dec 19, 2018 12:40 pm 写道: 这个看着挺结实。



上面的辣个长方型的 PVC 框架, 看上去不是很方便拆卸, 这个长方型的 PVC 框架不能快速方便的拆卸的话, 整个雪上飞放不进去我的小烂车, 还是白搭....

车顶上,像卡牙克一样
jimi
Grand General (大将)
Grand General (大将)
 
帖子: 22028
注册: 26 11月 2013 16:45
Member Number (论坛会员注册序列号): #203
地址: Newmarket
称呼: 吉米

Re: [DIY]Fishing for ideas:打算重新整一个Smitty Sled(雪上飞),请您给出点儿高招

楼层:#154  帖子Sergeantpepper » 19 12月 2018 14:32

This guy forgot to bring along the kitchen sink too...holly cow :laugh3

https://www.iceshanty.com/ice_fishing/index.php?topic=120514.0
"fishinJim how did you fasten the skis?"
"fishingjim : Glue and screws...Glue pulled apart when i pulled it sideways with a full load on it...
End caps with 4 screws going into the skis."

图片
Sergeantpepper
Grand General (大将)
Grand General (大将)
 
帖子: 13182
注册: 17 9月 2013 08:31
Member Number (论坛会员注册序列号): #6

Re: [DIY]Fishing for ideas:打算重新整一个Smitty Sled(雪上飞),请您给出点儿高招

楼层:#155  帖子johndxu » 03 3月 2019 14:56

jasontoronto @ 14 12月 2018 20:14 写道: 一路看过来,这嫡爱歪的目标至少四个:成本低,材质轻,结构硬,工艺精,看得鹅是越来越没有试一炮的信心。下回雪厚带个snowblower去开道。
VideoID: https://www.youtube.com/watch?v=MJJI9DcT0rk

据说,这种show blower 最快档比人步行快。那把blower拆了,也是一条慢跑雪狗吧?
johndxu
Lieutenant General (中将)
Lieutenant General (中将)
 
帖子: 1653
注册: 19 1月 2018 22:46
Member Number (论坛会员注册序列号): #2196
地址: 201 Consumers Rd., Toronto, ON M2J 4G8
称呼: 約翰

Re: [DIY]Fishing for ideas:打算重新整一个Smitty Sled(雪上飞),请您给出点儿高招

楼层:#156  帖子johndxu » 03 3月 2019 15:08

xiaolu @ 15 12月 2018 21:18 写道:
Sergeantpepper @ Sat Dec 15, 2018 8:08 pm 写道: 坐等站长傑作面世 :fishb

杰作不敢当. 搞了一个下午, 和滑雪板连接的是 PVC. 上面没用 PVC 是因为我要考虑上面部分可以随时安装, 拆卸, 于是就用了薄的比较轻的木板条儿, 然后一个倒扣烙饼就扣进 PVC 管儿里了. 不鸡道强度是否够. 但比较轻....

“倒扣烙饼就扣进 PVC 管儿里“是站长一大发明,使得拆卸拼装变得很容易。但是相对来说对四个PVC立柱来说要求的位置和安装的坚固。
上面的木板框架看起来比啥都好,轻便。
如果能把那两条铝条移到PVC管的中部,再加两条铝条加固在侧面PVC管的中部,那就不单解决小三劈腿的问题,也解决了四根棒棒的坚挺问题。但是PVC管上钻小孔,要有曲面垫圈+橡胶垫圈+螺栓+螺母固定,还要考虑前后两铝条的方便拆卸问题。
最后由 johndxu 编辑于 03 3月 2019 15:31,总共编辑了 3 次
johndxu
Lieutenant General (中将)
Lieutenant General (中将)
 
帖子: 1653
注册: 19 1月 2018 22:46
Member Number (论坛会员注册序列号): #2196
地址: 201 Consumers Rd., Toronto, ON M2J 4G8
称呼: 約翰

Re: [DIY]Fishing for ideas:打算重新整一个Smitty Sled(雪上飞),请您给出点儿高招

楼层:#157  帖子johndxu » 03 3月 2019 15:16

jasontoronto @ 18 12月 2018 19:52 写道:
johndxu @ 18 Dec 2018 19:36 写道:
吃瓜群众 @ 18 12月 2018 12:01 写道: 俩木片之间是用木螺丝连接的?这地方受力也是不小的,木头湿了之后是否还能不能吃住螺丝,俺表示怀疑~ :laugh3


两边的木板就固定一下框架,不受力,应该不会有问题。那两条铝条也确实能防小山防劈腿(Open Legs)给个 :+1


鹅也认为木板不会受很大的力。鹅最想知道的是那四根棒棒能有多坚挺。

如果坚持不卸那四根棒棒,会越来越坚挺。 :laugh3
johndxu
Lieutenant General (中将)
Lieutenant General (中将)
 
帖子: 1653
注册: 19 1月 2018 22:46
Member Number (论坛会员注册序列号): #2196
地址: 201 Consumers Rd., Toronto, ON M2J 4G8
称呼: 約翰

Re: [DIY]Fishing for ideas:打算重新整一个Smitty Sled(雪上飞),请您给出点儿高招

楼层:#158  帖子波澜不惊 » 06 3月 2019 15:37

johndxu @ 周日 3月 03, 2019 2:16 pm 写道:
jasontoronto @ 18 12月 2018 19:52 写道:
johndxu @ 18 Dec 2018 19:36 写道:

两边的木板就固定一下框架,不受力,应该不会有问题。那两条铝条也确实能防小山防劈腿(Open Legs)给个 :+1


鹅也认为木板不会受很大的力。鹅最想知道的是那四根棒棒能有多坚挺。

如果坚持不卸那四根棒棒,会越来越坚挺。 :laugh3

上车顶,毕竟不重
波澜不惊
General (上将)
General (上将)
 
帖子: 5449
注册: 25 5月 2014 06:52
Member Number (论坛会员注册序列号): #487

上一页

回到 It's All About Fishin' 钓鱼!

在线用户