定位打洞

相约钓鱼, 探讨钓技, 结交钓友, 分享渔获 。。。

定位打洞

楼层:#1  帖子赣西风 » 02 2月 2019 10:42

试了一下这个方法,加了个螺丝钉,定位倒是非常准确,可惜钻头入冰太慢,又把它取下来了。
您没有权限查看这个主题的附件(帖图)。 请先注册并登陆后访问。 谢谢! You have no permission to view this attachment. Please register and sign in. Thank you!
赣西风
Lieutenant General (中将)
Lieutenant General (中将)
 
帖子: 1998
注册: 23 3月 2014 20:13
Member Number (论坛会员注册序列号): #338
称呼: 西风

Re: 定位打洞

楼层:#2  帖子白雪丹枫 » 02 2月 2019 10:57

用self tapping screw如何?
白雪丹枫
Grand General (大将)
Grand General (大将)
 
帖子: 14857
注册: 30 9月 2013 17:14
Member Number (论坛会员注册序列号): #74
地址: Guelph, Ontario
称呼: 白将军

Re: 定位打洞

楼层:#3  帖子Sergeantpepper » 02 2月 2019 11:14

....or use the tap in the top pic :laugh3 ... with cutting flutes like self tapping screw :laugh3
Sergeantpepper
Grand General (大将)
Grand General (大将)
 
帖子: 13182
注册: 17 9月 2013 08:31
Member Number (论坛会员注册序列号): #6

Re: 定位打洞

楼层:#4  帖子Sergeantpepper » 02 2月 2019 11:15

In fact, it's the front cutting edge, like those on a hollow ice anchor, can do proper cutting....those screw threads are actually there to slow down the process, IMO

图片
Sergeantpepper
Grand General (大将)
Grand General (大将)
 
帖子: 13182
注册: 17 9月 2013 08:31
Member Number (论坛会员注册序列号): #6

Re: 定位打洞

楼层:#5  帖子赣西风 » 02 2月 2019 11:20

白雪丹枫 @ 周六 2月 02, 2019 9:57 am 写道: 用self tapping screw如何?


我需要一头带螺纹连接到冰钻上,另一头定位钻冰,现在是钻冰的这一头不给力,在考虑要不把螺丝干脆打磨成短尖锥形。
赣西风
Lieutenant General (中将)
Lieutenant General (中将)
 
帖子: 1998
注册: 23 3月 2014 20:13
Member Number (论坛会员注册序列号): #338
称呼: 西风

Re: 定位打洞

楼层:#6  帖子赣西风 » 02 2月 2019 11:22

Sergeantpepper @ 周六 2月 02, 2019 10:14 am 写道: ....or use the tap in the top pic :laugh3 ... with cutting flutes like self tapping screw :laugh3


椒叔你的想法和我一样啊? :roflmao
赣西风
Lieutenant General (中将)
Lieutenant General (中将)
 
帖子: 1998
注册: 23 3月 2014 20:13
Member Number (论坛会员注册序列号): #338
称呼: 西风

Re: 定位打洞

楼层:#7  帖子Sergeantpepper » 02 2月 2019 11:24

赣西风 @ Sat Feb 02, 2019 10:22 am 写道:
Sergeantpepper @ 周六 2月 02, 2019 10:14 am 写道: ....or use the tap in the top pic :laugh3 ... with cutting flutes like self tapping screw :laugh3


椒叔你的想法和我一样啊? :roflmao


but it's your 'tap' :roflmao
Sergeantpepper
Grand General (大将)
Grand General (大将)
 
帖子: 13182
注册: 17 9月 2013 08:31
Member Number (论坛会员注册序列号): #6

Re: 定位打洞

楼层:#8  帖子Pungo » 02 2月 2019 11:25

赣西风 @ Sat Feb 02, 2019 10:20 am 写道:
白雪丹枫 @ 周六 2月 02, 2019 9:57 am 写道: 用self tapping screw如何?


我需要一头带螺纹连接到冰钻上,另一头定位钻冰,现在是钻冰的这一头不给力,在考虑要不把螺丝干脆打磨成短尖锥形。

弄个小钻头安上?
Pungo
General (上将)
General (上将)
 
帖子: 10124
注册: 17 9月 2013 10:10
Member Number (论坛会员注册序列号): #10
地址: Richmond Hill
称呼: 司令

Re: 定位打洞

楼层:#9  帖子Sergeantpepper » 02 2月 2019 11:30

Pungo @ Sat Feb 02, 2019 10:25 am 写道:
赣西风 @ Sat Feb 02, 2019 10:20 am 写道:
白雪丹枫 @ 周六 2月 02, 2019 9:57 am 写道: 用self tapping screw如何?


我需要一头带螺纹连接到冰钻上,另一头定位钻冰,现在是钻冰的这一头不给力,在考虑要不把螺丝干脆打磨成短尖锥形。

弄个小钻头安上?


:up except you cannot thread up the other end of the twist drill for attaching it to the auger's shaft, it's hardened steel :laugh3
Sergeantpepper
Grand General (大将)
Grand General (大将)
 
帖子: 13182
注册: 17 9月 2013 08:31
Member Number (论坛会员注册序列号): #6

Re: 定位打洞

楼层:#10  帖子alfishing » 02 2月 2019 11:54

这个tip 我做过,效果不错。西风兄说的太慢,估计一是tip 太长,二是螺丝有阻碍,就像椒sir说的,可以考虑磨成三角形。磨成像gas auger那样的tip效果最好。但螺丝太小恐怕强度不够。
alfishing
Colonel (上校)
 
帖子: 154
注册: 29 3月 2014 03:17
Member Number (论坛会员注册序列号): #343

Re: 定位打洞

楼层:#11  帖子白雪丹枫 » 02 2月 2019 12:20

Sergeantpepper @ 周六 2月 02, 2019 10:30 am 写道:
Pungo @ Sat Feb 02, 2019 10:25 am 写道:
赣西风 @ Sat Feb 02, 2019 10:20 am 写道:

我需要一头带螺纹连接到冰钻上,另一头定位钻冰,现在是钻冰的这一头不给力,在考虑要不把螺丝干脆打磨成短尖锥形。

弄个小钻头安上?


:up except you cannot thread up the other end of the twist drill for attaching it to the auger's shaft, it's hardened steel :laugh3


Easy. Weld the tap to an insert with ousdie threaded, then screw in the thaft.
白雪丹枫
Grand General (大将)
Grand General (大将)
 
帖子: 14857
注册: 30 9月 2013 17:14
Member Number (论坛会员注册序列号): #74
地址: Guelph, Ontario
称呼: 白将军

Re: 定位打洞

楼层:#12  帖子Sergeantpepper » 02 2月 2019 12:24

....现时的tip有点过长, 越短越好, 能定位, 不拖时

下面类的drill bit 最合用, 但要在另一端加絲扣有难度.....有焊接方便就好
您没有权限查看这个主题的附件(帖图)。 请先注册并登陆后访问。 谢谢! You have no permission to view this attachment. Please register and sign in. Thank you!
Sergeantpepper
Grand General (大将)
Grand General (大将)
 
帖子: 13182
注册: 17 9月 2013 08:31
Member Number (论坛会员注册序列号): #6

Re: 定位打洞

楼层:#13  帖子赣西风 » 02 2月 2019 12:45

Sergeantpepper @ 周六 2月 02, 2019 11:24 am 写道: ....现时的tip有点过长, 越短越好, 能定位, 不拖时

下面类的drill bit 最合用, 但要在另一端加絲扣有难度.....有焊接方便就好


最下面的肯定不可以,冰会卡住不往下切,估计一点都钻不下去。 :roflmao
赣西风
Lieutenant General (中将)
Lieutenant General (中将)
 
帖子: 1998
注册: 23 3月 2014 20:13
Member Number (论坛会员注册序列号): #338
称呼: 西风

Re: 定位打洞

楼层:#14  帖子赣西风 » 02 2月 2019 12:47

alfishing @ 周六 2月 02, 2019 10:54 am 写道: 这个tip 我做过,效果不错。西风兄说的太慢,估计一是tip 太长,二是螺丝有阻碍,就像椒sir说的,可以考虑磨成三角形。磨成像gas auger那样的tip效果最好。但螺丝太小恐怕强度不够。


准备这样试一试。
赣西风
Lieutenant General (中将)
Lieutenant General (中将)
 
帖子: 1998
注册: 23 3月 2014 20:13
Member Number (论坛会员注册序列号): #338
称呼: 西风

Re: 定位打洞

楼层:#15  帖子赣西风 » 02 2月 2019 12:53

白雪丹枫 @ 周六 2月 02, 2019 11:20 am 写道:
Sergeantpepper @ 周六 2月 02, 2019 10:30 am 写道:
Pungo @ Sat Feb 02, 2019 10:25 am 写道:
弄个小钻头安上?


:up except you cannot thread up the other end of the twist drill for attaching it to the auger's shaft, it's hardened steel :laugh3


Easy. Weld the tap to an insert with ousdie threaded, then screw in the thaft.


昨天试钻的过程中发现我加的螺丝有点点偏心了,所以另外加锥形头还有点难度了。
赣西风
Lieutenant General (中将)
Lieutenant General (中将)
 
帖子: 1998
注册: 23 3月 2014 20:13
Member Number (论坛会员注册序列号): #338
称呼: 西风

Re: 定位打洞

楼层:#16  帖子阿恩 » 02 2月 2019 17:50

赣西风 @ 周六 2月 02, 2019 10:20 am 写道:
白雪丹枫 @ 周六 2月 02, 2019 9:57 am 写道: 用self tapping screw如何?


我需要一头带螺纹连接到冰钻上,另一头定位钻冰,现在是钻冰的这一头不给力,在考虑要不把螺丝干脆打磨成短尖锥形。

也许用一根合适大小的普通钻头,另一头绞成需要的螺纹,如果可以的话。
阿恩
General (上将)
General (上将)
 
帖子: 6684
注册: 18 11月 2013 11:46
Member Number (论坛会员注册序列号): #193
地址: Steeles & Don Mills, North York

Re: 定位打洞

楼层:#17  帖子Sergeantpepper » 02 2月 2019 18:03

貌似可按Eskimo 的DIY 一炮, 那Centering Point 用SS flat bar 夠硬亦可手动加工....什至可先用普通mild steel flat bar 先試試.....把手冰钻軸尾那个已攻了內牙的孔加大到flat bar 的阔度就是, 或用needle file 銼出个一字孔更佳

图片
您没有权限查看这个主题的附件(帖图)。 请先注册并登陆后访问。 谢谢! You have no permission to view this attachment. Please register and sign in. Thank you!
Sergeantpepper
Grand General (大将)
Grand General (大将)
 
帖子: 13182
注册: 17 9月 2013 08:31
Member Number (论坛会员注册序列号): #6


回到 It's All About Fishin' 钓鱼!

在线用户