定位打洞
发表于 : 02 2月 2019 10:42
试了一下这个方法,加了个螺丝钉,定位倒是非常准确,可惜钻头入冰太慢,又把它取下来了。
白雪丹枫 @ 周六 2月 02, 2019 9:57 am 写道: 用self tapping screw如何?
Sergeantpepper @ 周六 2月 02, 2019 10:14 am 写道: ....or use the tap in the top pic ... with cutting flutes like self tapping screw
赣西风 @ Sat Feb 02, 2019 10:22 am 写道:Sergeantpepper @ 周六 2月 02, 2019 10:14 am 写道: ....or use the tap in the top pic ... with cutting flutes like self tapping screw
椒叔你的想法和我一样啊?
赣西风 @ Sat Feb 02, 2019 10:20 am 写道:白雪丹枫 @ 周六 2月 02, 2019 9:57 am 写道: 用self tapping screw如何?
我需要一头带螺纹连接到冰钻上,另一头定位钻冰,现在是钻冰的这一头不给力,在考虑要不把螺丝干脆打磨成短尖锥形。
Pungo @ Sat Feb 02, 2019 10:25 am 写道:赣西风 @ Sat Feb 02, 2019 10:20 am 写道:白雪丹枫 @ 周六 2月 02, 2019 9:57 am 写道: 用self tapping screw如何?
我需要一头带螺纹连接到冰钻上,另一头定位钻冰,现在是钻冰的这一头不给力,在考虑要不把螺丝干脆打磨成短尖锥形。
弄个小钻头安上?
Sergeantpepper @ 周六 2月 02, 2019 10:30 am 写道:Pungo @ Sat Feb 02, 2019 10:25 am 写道:赣西风 @ Sat Feb 02, 2019 10:20 am 写道:
我需要一头带螺纹连接到冰钻上,另一头定位钻冰,现在是钻冰的这一头不给力,在考虑要不把螺丝干脆打磨成短尖锥形。
弄个小钻头安上?
except you cannot thread up the other end of the twist drill for attaching it to the auger's shaft, it's hardened steel
Sergeantpepper @ 周六 2月 02, 2019 11:24 am 写道: ....现时的tip有点过长, 越短越好, 能定位, 不拖时
下面类的drill bit 最合用, 但要在另一端加絲扣有难度.....有焊接方便就好
alfishing @ 周六 2月 02, 2019 10:54 am 写道: 这个tip 我做过,效果不错。西风兄说的太慢,估计一是tip 太长,二是螺丝有阻碍,就像椒sir说的,可以考虑磨成三角形。磨成像gas auger那样的tip效果最好。但螺丝太小恐怕强度不够。
白雪丹枫 @ 周六 2月 02, 2019 11:20 am 写道:Sergeantpepper @ 周六 2月 02, 2019 10:30 am 写道:Pungo @ Sat Feb 02, 2019 10:25 am 写道:
弄个小钻头安上?
except you cannot thread up the other end of the twist drill for attaching it to the auger's shaft, it's hardened steel
Easy. Weld the tap to an insert with ousdie threaded, then screw in the thaft.
赣西风 @ 周六 2月 02, 2019 10:20 am 写道:白雪丹枫 @ 周六 2月 02, 2019 9:57 am 写道: 用self tapping screw如何?
我需要一头带螺纹连接到冰钻上,另一头定位钻冰,现在是钻冰的这一头不给力,在考虑要不把螺丝干脆打磨成短尖锥形。