万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

相约钓鱼, 探讨钓技, 结交钓友, 分享渔获 。。。

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#76  帖子河上笑 » 08 6月 2018 12:20

Pungo @ 周五 6月 08, 2018 11:29 am 写道:
河上笑 @ Fri Jun 08, 2018 11:12 am 写道:
Sergeantpepper @ 周五 6月 08, 2018 10:55 am 写道: 喜见上校的構想基本上已有定案, 但个人还是有些想法
胶板造底座簡单直接, 但板厚如果不足则探竿旋转时會wobble, 不欲也, 板厚能有1至2D較理想
我同意Eric 提議用的套筒, 但一般NPS 好难得一管之OD能剛好配合另一管之ⅠD 以达Sliding fit 配合, 所以我提議了用双omega bracket, 铁片配件較易弄得适当地与探管配合...

剛有新念头, 只有PVC tee fitting 才能更易做到套筒功能...
进而想像到整个fixture 根本最好就用全PVC管结構, 底座中间一个垂直Tee 做套筒, 结扎结帳


椒Sir言之有理 :up :shake 塑料菜板的厚度基本没有超过半寸的,探杆难以保持垂直。您说的PVC fitting我昨天在homedepot没找到,很奇怪PVC fitting的材料非常少,没有这些接头套筒之类的东西。改天我去Lowe看看,或者某家专门卖plumbing材料的店里有更多选择。

用两个Tee做成一个H形,平放在冰面洞口上,中间加一个垂直的四通,探鱼器管子加一个直通,防止管子掉下去。黑色ABS就很好,便宜冰上醒目。


多谢司令高招 :up :shake 我得要去店里看看能不能找到这些管件,homedepot里的PVC管件太少啦。
河上笑
General (上将)
General (上将)
 
帖子: 7400
注册: 10 9月 2014 17:59
Member Number (论坛会员注册序列号): #787
地址: Markham, Ontario

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#77  帖子johndxu » 08 6月 2018 14:38

可以用割下的边角料来增加底板的高度。 如图:一块两块都可以。注意要先上好小螺钉再一次打大孔。
您没有权限查看这个主题的附件(帖图)。 请先注册并登陆后访问。 谢谢! You have no permission to view this attachment. Please register and sign in. Thank you!
johndxu
Lieutenant General (中将)
Lieutenant General (中将)
 
帖子: 1653
注册: 19 1月 2018 22:46
Member Number (论坛会员注册序列号): #2196
地址: 201 Consumers Rd., Toronto, ON M2J 4G8
称呼: 約翰

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#78  帖子Sergeantpepper » 08 6月 2018 14:55

Lowes electrical dept
1/2" pvc electrical conduit
This 8'L (?) conduit has one end expanded for extension connection purpose..
Cut off the expanded end, about 3"L, and it can be used as the sliding/turning sleeve..
Since there are no tees & elbows for these conduits, as there are junction box for the job, the fixture cannot be completed using entirely conduit & fittings...but IMO the sliding/turning sleeve function one can get out of such is the best..
This is best working with the Wooden Tee as I earlier suggested...use omega bracket to fix the sleeve on the WoodenTee..(use 2x3 for the wooden tee is good enough)
您没有权限查看这个主题的附件(帖图)。 请先注册并登陆后访问。 谢谢! You have no permission to view this attachment. Please register and sign in. Thank you!
Sergeantpepper
Grand General (大将)
Grand General (大将)
 
帖子: 13182
注册: 17 9月 2013 08:31
Member Number (论坛会员注册序列号): #6

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#79  帖子Sergeantpepper » 08 6月 2018 15:19

Lowes plumbing dept
3/4" PEX piping & fitting
(PEX suitable for hot water purpose, made of polyethylene, may take different glue from those for ABS, PVC, better ask around)

This pipe & it's fittings can be used to finish the complete fixture, except inside the Tee there's a shoulder of smaller dia., which is used as a stopper for pipe insertion...it may take some extra work to eliminate this shoulder to turn the Tee into a good sliding/turning sleeve ( General White's show time now, may be :roflmao ...job to be done on a centre lathe)
您没有权限查看这个主题的附件(帖图)。 请先注册并登陆后访问。 谢谢! You have no permission to view this attachment. Please register and sign in. Thank you!
Sergeantpepper
Grand General (大将)
Grand General (大将)
 
帖子: 13182
注册: 17 9月 2013 08:31
Member Number (论坛会员注册序列号): #6

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#80  帖子河上笑 » 08 6月 2018 15:51

Sergeantpepper @ 周五 6月 08, 2018 3:19 pm 写道: Lowes plumbing dept
3/4" PEX piping & fitting
(PEX suitable for hot water purpose, made of polyethylene, may take different glue from those for ABS, PVC, better ask around)

This pipe & it's fittings can be used to finish the complete fixture, except inside the Tee there's a shoulder of smaller dia., which is used as a stopper for pipe insertion...it may take some extra work to eliminate this shoulder to turn the Tee into a good sliding/turning sleeve ( General White's show time now, may be :roflmao ...job to be done on a centre lathe)


椒Sir费心了,这个方案听起来简单了,我要去店里看看材料 。 :up
河上笑
General (上将)
General (上将)
 
帖子: 7400
注册: 10 9月 2014 17:59
Member Number (论坛会员注册序列号): #787
地址: Markham, Ontario

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#81  帖子河上笑 » 08 6月 2018 15:55

johndxu @ 周五 6月 08, 2018 2:38 pm 写道: 可以用割下的边角料来增加底板的高度。 如图:一块两块都可以。注意要先上好小螺钉再一次打大孔。


明白你的意思了,兄台不愧是工程师啊,这图是顺手就来,佩服佩服。 :up :up
河上笑
General (上将)
General (上将)
 
帖子: 7400
注册: 10 9月 2014 17:59
Member Number (论坛会员注册序列号): #787
地址: Markham, Ontario

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#82  帖子白雪丹枫 » 08 6月 2018 16:06

河上笑 @ 周四 6月 07, 2018 10:35 pm 写道:
johndxu @ 周四 6月 07, 2018 1:34 pm 写道: 到dollar店去买一块圆形的塑料切菜板,然后画线,用钻头,钢丝锯,多功能Crafter KIT 等切割打磨。
不好意思,对面的边缘还要开一细槽以便鱼线可以滑出。

多谢兄台,塑料菜板确实是好主意,轻便、防水、冷天不变形的优点是不二之选。 :up 我已经买到了支杆,下面就差买菜板切割钻洞了。 :shake


我觉得木板更好。厚度随便买,容易加工,轻便,上一层清漆就可以防水,也不会变形。塑料件冬天会发脆,不知道能不能顶住零下20度的低温天气。
白雪丹枫
Grand General (大将)
Grand General (大将)
 
帖子: 14857
注册: 30 9月 2013 17:14
Member Number (论坛会员注册序列号): #74
地址: Guelph, Ontario
称呼: 白将军

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#83  帖子Sergeantpepper » 08 6月 2018 16:50

白雪丹枫 @ Fri Jun 08, 2018 4:06 pm 写道:
河上笑 @ 周四 6月 07, 2018 10:35 pm 写道:
johndxu @ 周四 6月 07, 2018 1:34 pm 写道: 到dollar店去买一块圆形的塑料切菜板,然后画线,用钻头,钢丝锯,多功能Crafter KIT 等切割打磨。
不好意思,对面的边缘还要开一细槽以便鱼线可以滑出。

多谢兄台,塑料菜板确实是好主意,轻便、防水、冷天不变形的优点是不二之选。 :up 我已经买到了支杆,下面就差买菜板切割钻洞了。 :shake


我觉得木板更好。厚度随便买,容易加工,轻便,上一层清漆就可以防水,也不会变形。塑料件冬天会发脆,不知道能不能顶住零下20度的低温天气。


视频那原装货不正是全塑的吗? :fishb
Sergeantpepper
Grand General (大将)
Grand General (大将)
 
帖子: 13182
注册: 17 9月 2013 08:31
Member Number (论坛会员注册序列号): #6

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#84  帖子白雪丹枫 » 08 6月 2018 17:04

Sergeantpepper @ 周五 6月 08, 2018 4:50 pm 写道:
白雪丹枫 @ Fri Jun 08, 2018 4:06 pm 写道:
河上笑 @ 周四 6月 07, 2018 10:35 pm 写道:
多谢兄台,塑料菜板确实是好主意,轻便、防水、冷天不变形的优点是不二之选。 :up 我已经买到了支杆,下面就差买菜板切割钻洞了。 :shake


我觉得木板更好。厚度随便买,容易加工,轻便,上一层清漆就可以防水,也不会变形。塑料件冬天会发脆,不知道能不能顶住零下20度的低温天气。


视频那原装货不正是全塑的吗? :fishb


塑料菜板的塑料,跟工业塑料有差别。如果是用电木塑料板,一点没问题,但就比木板重多了。我本来考虑用lexan glass, 但还是怀疑它在低温下的表现。
白雪丹枫
Grand General (大将)
Grand General (大将)
 
帖子: 14857
注册: 30 9月 2013 17:14
Member Number (论坛会员注册序列号): #74
地址: Guelph, Ontario
称呼: 白将军

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#85  帖子john8848 » 08 6月 2018 17:38

上校,照片中这个东西是我用来冬钓固定相机线的,旋转它可以旋转相机,正好在8的洞上用。把它反过来,它有一段类似旋轴可以防倾倒,需要的话,我有。
您没有权限查看这个主题的附件(帖图)。 请先注册并登陆后访问。 谢谢! You have no permission to view this attachment. Please register and sign in. Thank you!
john8848
Lieutenant General (中将)
Lieutenant General (中将)
 
帖子: 3762
注册: 30 10月 2013 20:44
Member Number (论坛会员注册序列号): #155
地址: Taunton & Brock, Whitby

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#86  帖子阿恩 » 08 6月 2018 18:05

河上笑 @ 周四 6月 07, 2018 10:55 pm 写道:
eric_gao @ 周四 6月 07, 2018 3:39 pm 写道:
yangzw2002 @ 周四 6月 07, 2018 9:28 am 写道: 这个估摸着高兄的router能做出来


我的建议也是用细木工板,用router做出形状,然后喷防水漆。
白色菜板也行,本身就防水,我都可以切。厚度不超过2寸,都没问题。
中间的好搞一些。
用一节粗一点的做套筒,再用一节细一些的做可以旋转的。内心的可以钻一系列的洞,可以插一个pin。卡在外圈上不会掉落,但也不影响旋转。

老江也要做一个,上校可以一起商量出图纸,我可以帮忙加工。 :up :shake

老高呢你终于来了,一出现就带来福音。太感谢啦 :up :shake
我给你报告一下,我今晚在CanadianTire闲逛,无意中看到一个冲马桶的工具,一根硬塑料的管子。 :roflmao 我一想这不就是我需要的支杆吗?不长不短,管径尺寸正好跟探头的扣件合适,才20几刀,于是我把它买了,然后去Homedepot找PVC管子的配件,嘿,还真找到几个,我东拼西凑把管件装在支杆上做成一个简单的手柄,现在基本就是这个样子滴,就差中间那块板子啦,准备用塑料菜板钻孔。但支杆要能旋转,还要保持垂直,这是难点。 :laugh3

在PVC pipe顶端装个全方位的level,不过不确定level里面的液体会不会结冰。
最后由 阿恩 编辑于 08 6月 2018 18:06,总共编辑了 1 次
阿恩
General (上将)
General (上将)
 
帖子: 6684
注册: 18 11月 2013 11:46
Member Number (论坛会员注册序列号): #193
地址: Steeles & Don Mills, North York

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#87  帖子Sergeantpepper » 08 6月 2018 18:05

http://www.leevalley.com/us/garden/page.aspx?cat=2,33141&p=67332

其中这A.. Slip Tee 內边应該没有 shoulder, 故PVC管可直接贯通, 合套筒用, 不像plumbing tee 需要加工鏟去內边shoulder
Sergeantpepper
Grand General (大将)
Grand General (大将)
 
帖子: 13182
注册: 17 9月 2013 08:31
Member Number (论坛会员注册序列号): #6

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#88  帖子河上笑 » 08 6月 2018 19:17

john8848 @ 周五 6月 08, 2018 5:38 pm 写道: 上校,照片中这个东西是我用来冬钓固定相机线的,旋转它可以旋转相机,正好在8的洞上用。把它反过来,它有一段类似旋轴可以防倾倒,需要的话,我有。

哇,这个看起来有点意思,我那个PVC支杆1/2寸能从中间穿过去吗?如果尺寸对,我那天钓鱼从你家路过来看看。
多谢John兄 :shake
河上笑
General (上将)
General (上将)
 
帖子: 7400
注册: 10 9月 2014 17:59
Member Number (论坛会员注册序列号): #787
地址: Markham, Ontario

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#89  帖子xiaolu » 08 6月 2018 19:33

河上笑同鸡的"嘎民"费事烦得, 真乃是高大上啊.相比之下, 鹅的"老乱死", 还有辣个谁谁谁的H-鸟"河里个死", 怎么都是个死. :laugh3
xiaolu
Site Admin (站长)
 
帖子: 42626
注册: 17 9月 2013 06:22
Member Number (论坛会员注册序列号): #1
地址: Maple, Vaughan

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#90  帖子河上笑 » 08 6月 2018 19:38

xiaolu @ 周五 6月 08, 2018 7:33 pm 写道: 河上笑同鸡的"嘎民"费事烦得, 真乃是高大上啊.相比之下, 鹅的"老乱死", 还有辣个谁谁谁的H-鸟"河里个死", 怎么都是个死. :laugh3

黑猫白猫抓到鱼的才是好猫,费事烦同理。找到鱼的是好费事烦,找不到鱼的是好费事好烦人 :roflmao
河上笑
General (上将)
General (上将)
 
帖子: 7400
注册: 10 9月 2014 17:59
Member Number (论坛会员注册序列号): #787
地址: Markham, Ontario

Re: 万能神坛,有什么高招可以DIY一个Garmin的Ice Fishing Mount

楼层:#91  帖子john8848 » 08 6月 2018 19:54

河上笑 @ 周五 6月 08, 2018 7:17 pm 写道:
john8848 @ 周五 6月 08, 2018 5:38 pm 写道: 上校,照片中这个东西是我用来冬钓固定相机线的,旋转它可以旋转相机,正好在8的洞上用。把它反过来,它有一段类似旋轴可以防倾倒,需要的话,我有。

哇,这个看起来有点意思,我那个PVC支杆1/2寸能从中间穿过去吗?如果尺寸对,我那天钓鱼从你家路过来看看。
多谢John兄 :shake

1/2" 没问题,过来拿吧! :shake
john8848
Lieutenant General (中将)
Lieutenant General (中将)
 
帖子: 3762
注册: 30 10月 2013 20:44
Member Number (论坛会员注册序列号): #155
地址: Taunton & Brock, Whitby

上一页

回到 It's All About Fishin' 钓鱼!

在线用户

cron