Toronto Fishing Forum

原有ice Auger： normark 6"

原有电钻：black deck 18v,(充满实测电压20.8v) 入门级18V，$50促销价购入

连接件：lebaron 买来的，价格8.63 plus tax = $9.75

测试地点，GTA某小池塘

实际冰情，4寸黑冰

测试结果如下：问题一：不够稳

试图加压力解决，出现问题二：扭矩不足，被冰卡住，有烧坏电钻的可能

摇摇晃晃用了一分多钟，打出一个8寸左右形状不规则的洞

本人结论，不如老老实实用手打，一分钟打四个不成问题

也许是电钻不够高级?

各位尽管支招，看看啥问题

对俺们简单易行派是一个非常非常沉重的打击呀

这是今天另外一份不同的冰钻实验报告


john8848 » 2013年 12月 11日 星期三 11:47 pm

边部:

以下是Banana老兄的用后感言：
好东西！看了楼主的消息，也去买了一个。今天试用了一下。赶紧来汇报效果。

刀口非常锋利，打一个洞也就用5秒钟。能打多少洞主要看手钻的扭矩和电池的质量。
我用的是milwaukee 18v. CAT NO.2602-20 输出525 in-lbs. 电池是M18 XC输出3.0 amp-hour。可以在-18C的温度下工作。一个电池打了16个洞，电量显示还剩了两格电。


没有好的手钻就算了吧。 如果有现成的好手钻在，强烈推荐这个。太超值了！！

是的电钻的牌子不行。要名牌。像Mikita和Delwade.其他牌子感觉都不靠谱。

jeffrey2k 写道:原有ice Auger： normark 6"

原有电钻：black deck 18v,(充满实测电压20.8v) 入门级18V，$50促销价购入

连接件：lebaron 买来的，价格8.63 plus tax = $9.75

测试地点，GTA某小池塘

实际冰情，4寸黑冰

测试结果如下：问题一：不够稳

试图加压力解决，出现问题二：扭矩不足，被冰卡住，有烧坏电钻的可能

摇摇晃晃用了一分多钟，打出一个8寸左右形状不规则的洞

本人结论，不如老老实实用手打，一分钟打四个不成问题

也许是电钻不够高级?

各位尽管支招，看看啥问题

俺电钻是迪卧的，电池20V，3．0容量厘电，手摇钻8寸，一尺＝12寸，轻松打8个洞，俺的电钻有手把，打洞很稳，照片太大上传不去，哈哈哈


您要开慢档，一档试试！

看看这个钻。
[youtube]http://www.youtube.com/watch?v=sgny9A3GX90[/youtube]

有可能是你的电钻的问题，还有可能是你的钻头刀片是不是需要磨一下了？其实我还见过有人用Roybi的电钻呢。

我想钻冰和钻墙一个道理，是不是得用冲击钻。普通手钻钻木头还行，如果扭矩太大。肯定吃不消。

手转最好是Milwaukee Fuel, Bosch.

RIDGID型号＃R86008K性假比不错: 160 USD

提供535英寸扭矩, LED灯，锂电池，RIDGID终身服务: 免费电池。免费部件。免费服务。1/2英寸的单套棘轮夹头锁紧机构.

john8848 写道:手转最好是Milwaukee Fuel, Bosch.

RIDGID型号＃R86008K性假比不错: 160 USD

提供535英寸扭矩, LED灯，锂电池，RIDGID终身服务: 免费电池。免费部件。免费服务。1/2英寸的单套棘轮夹头锁紧机构.

你在美国?

谢谢你的报告，我就是看了这个报告决定放弃这种电钻驱动式冰钻，原因有三：１：我没有好的电钻Milwaukee，Mikita，DeWALT，Hitachi ；2：没有手动的冰钻；３：没有连接1和2 的ADAPTAR。如果把这三个东西都买齐，比买站长的那种钻还贵，所以我决定买站长的那种钻，一步到位！

XUYCA 写道:我想钻冰和钻墙一个道理，是不是得用冲击钻。普通手钻钻木头还行，如果扭矩太大。肯定吃不消。

不对，不能用冲击挡，只能用drill挡，hammer 挡是把东西打碎，ice auger 上是刀片，是把冰一层一层大刮开，所以必须用drill 挡。

阿恩 写道:

XUYCA 写道:我想钻冰和钻墙一个道理，是不是得用冲击钻。普通手钻钻木头还行，如果扭矩太大。肯定吃不消。

不对，不能用冲击挡，只能用drill挡，hammer 挡是把东西打碎，ice auger 上是刀片，是把冰一层一层大刮开，所以必须用drill 挡。

有道理。看了一下，我有一把18v lxt Mikita手电钻。平时用很给力。去哪里买连接设备？准备搞一个玩玩。

XUYCA 写道:

阿恩 写道:

XUYCA 写道:我想钻冰和钻墙一个道理，是不是得用冲击钻。普通手钻钻木头还行，如果扭矩太大。肯定吃不消。

不对，不能用冲击挡，只能用drill挡，hammer 挡是把东西打碎，ice auger 上是刀片，是把冰一层一层大刮开，所以必须用drill 挡。

有道理。看了一下，我有一把18v lxt Mikita手电钻。平时用很给力。去哪里买连接设备？准备搞一个玩玩。

我的钻是这款。
http://www.makitatools.com/en-us/Module ... ame=LXFD01
不知道够力不？

I have so many experience for the Cordless Drill convert to Ice Drill.
To make long story short, Go buy a premium drill and you will be all set.
Dewalt 18V or 24V with higher Torque will do the trick. Go buy one in Crappy Tire and if it is not work for you then go return it.
I am not an expert but my 15+years ice fishing experience tell and there were lots of lessons i learned in order to share my experience to our fellow members.

p.s. Hold tight on the auger once it cut close to the end of the hole, if not, it might twist your arm and end with a long term treatment in massage therapy!

FYI- I am using Strikemaster Electric Ice Drill wih 8 inches and this is the fourth year now and it is one of my best investment in ice fishing equipments.

Thank you for sharing your experience with us, specially the following points:" Hold tight on the auger once it cut close to the end of the hole, if not, it might twist your arm and end with a long term treatment in massage therapy!"

DIYUSOCCERLO 写道:I have so many experience for the Cordless Drill convert to Ice Drill.
To make long story short, Go buy a premium drill and you will be all set.
Dewalt 18V or 24V with higher Torque will do the trick. Go buy one in Crappy Tire and if it is not work for you then go return it.
I am not an expert but my 15+years ice fishing experience tell and there were lots of lessons i learned in order to share my experience to our fellow members.

p.s. Hold tight on the auger once it cut close to the end of the hole, if not, it might twist your arm and end with a long term treatment in massage therapy!

FYI- I am using Strikemaster Electric Ice Drill wih 8 inches and this is the fourth year now and it is one of my best investment in ice fishing equipments.

DIYUSOCCERLO 写道:I have so many experience for the Cordless Drill convert to Ice Drill.
To make long story short, Go buy a premium drill and you will be all set.
Dewalt 18V or 24V with higher Torque will do the trick. Go buy one in Crappy Tire and if it is not work for you then go return it.
I am not an expert but my 15+years ice fishing experience tell and there were lots of lessons i learned in order to share my experience to our fellow members.

p.s. Hold tight on the auger once it cut close to the end of the hole, if not, it might twist your arm and end with a long term treatment in massage therapy!

FYI- I am using Strikemaster Electric Ice Drill wih 8 inches and this is the fourth year now and it is one of my best investment in ice fishing equipments.

Thanks so much for sharing your great experience. I also heard of this Strikemaster Electric Ice Auger (and I saw one guy using it the last winter when I ice fished with him. In fact I will meet him again tomorrow morning at a breakfast gathering in Orillia)

I also just recently bought a battery-powered electrical auger, the ICON:

ICON ?
or ION
or NOI
or NOT

Sergeantpepper 写道:ICON ?
or ION
or NOI
or NOT

ha. I mean ION

...or ZOH, HOZ
Just kidding with you....kinda bored

john8848 写道:手转最好是Milwaukee Fuel, Bosch.

RIDGID型号＃R86008K性假比不错: 160 USD

提供535英寸扭矩, LED灯，锂电池，RIDGID终身服务: 免费电池。免费部件。免费服务。1/2英寸的单套棘轮夹头锁紧机构.

介个手钻加拿大有卖的吗？

疯鱼 写道:

john8848 写道:手转最好是Milwaukee Fuel, Bosch.

RIDGID型号＃R86008K性假比不错: 160 USD

提供535英寸扭矩, LED灯，锂电池，RIDGID终身服务: 免费电池。免费部件。免费服务。1/2英寸的单套棘轮夹头锁紧机构.

介个手钻加拿大有卖的吗？

有，在homedeport 可以买到。

XUYCA 写道:

XUYCA 写道:

阿恩 写道:

XUYCA 写道:我想钻冰和钻墙一个道理，是不是得用冲击钻。普通手钻钻木头还行，如果扭矩太大。肯定吃不消。

不对，不能用冲击挡，只能用drill挡，hammer 挡是把东西打碎，ice auger 上是刀片，是把冰一层一层大刮开，所以必须用drill 挡。

有道理。看了一下，我有一把18v lxt Mikita手电钻。平时用很给力。去哪里买连接设备？准备搞一个玩玩。

我的钻是这款。
http://www.makitatools.com/en-us/Module ... ame=LXFD01
不知道够力不？

应该可以，this is one of the best brand in the market, good drills will have good torque, when you try to drill, set the torque at the medium setting to start, when it get jammed then increase the torque gradually and hold the drill firmly, if your drill comes with side handle, that will help a lot. I don't know ice fishing, I just use drills in my jobs. I think you also can use a impact drill, that might work even better, if I get any chance, I will try to figure out.